-
1 Donkin, Bryan III
SUBJECT AREA: Mechanical, pneumatic and hydraulic engineering, Steam and internal combustion engines[br]b. 29 August 1835 London, Englandd. 4 March 1902 Brussels, Belgium[br]English mechanical engineer.[br]Bryan Donkin was the eldest son of John Donkin (1802–54) and grandson of Bryan Donkin I (1768–1855). He was educated at University College, London, and at the Ecole Centrale des Arts et Métiers in Paris, and then served an apprenticeship in the firm established by his grandfather. He assisted his uncle, Bryan Donkin II (1809–93), in setting up paper mills at St Petersburg. He became a partner in the Donkin firm in 1868 and Chairman in 1889, and retained this position after the amalgamation with Clench \& Co. of Chesterfield in 1900. Bryan Donkin was one of the first engineers to carry out scientific tests on steam engines and boilers, the results of his experiments being reported in many papers to the engineering institutions. In the 1890s his interests extended to the internal-combustion engine and he translated Rudolf Diesel's book Theory and Construction of a Rational Heat Motor. He was a frequent contributor to the weekly journal The Engineer. He was a member of the Institution of Civil Engineers and of the Institution of Mechanical Engineers, as well as of many other societies, including the Royal Institution, the American Society of Mechanical Engineers, the Société Industrielle de Mulhouse and the Verein Deutscher Ingenieure. In his experimental work he often collaborated with others, notably Professor A.B.W.Kennedy (1847–1928), with whom he was also associated in the consulting engineering firm of Kennedy \& Donkin.[br]Principal Honours and DistinctionsVice-President, Institution of Mechanical Engineers 1901. Institution of Civil Engineers, Telford premiums 1889, 1891; Watt Medal 1894; Manby premium 1896.Bibliography1894, Gas, Oil and Air Engines, London.1896, with A.B.W.Kennedy, Experiments on Steam Boilers, London. 1898, Heat Efficiency of Steam Boilers, London.RTS -
2 Bulleid, Oliver Vaughan Snell
[br]b. 19 September 1882 Invercargill, New Zealandd. 25 April 1970 Malta[br]New Zealand (naturalized British) locomotive engineer noted for original experimental work in the 1940s and 1950s.[br]Bulleid's father died in 1889 and mother and son returned to the UK from New Zealand; Bulleid himself became a premium apprentice under H.A. Ivatt at Doncaster Works, Great Northern Railway (GNR). After working in France and for the Board of Trade, Bulleid returned to the GNR in 1912 as Personal Assistant to Chief Mechanical Engineer H.N. Gresley. After a break for war service, he returned as Assistant to Gresley on the latter's appointment as Chief Mechanical Engineer of the London \& North Eastern Railway in 1923. He was closely associated with Gresley during the late 1920s and early 1930s.In 1937 Bulleid was appointed Chief Mechanical Engineer of the Southern Railway (SR). Concentration of resources on electrification had left the Southern short of up-to-date steam locomotives, which Bulleid proceeded to provide. His first design, the "Merchant Navy" class 4–6– 2, appeared in 1941 with chain-driven valve gear enclosed in an oil-bath, and other novel features. A powerful "austerity" 0−6−0 appeared in 1942, shorn of all inessentials to meet wartime conditions, and a mixed-traffic 4−6−2 in 1945. All were largely successful.Under Bulleid's supervision, three large, mixed-traffic, electric locomotives were built for the Southern's 660 volt DC system and incorporated flywheel-driven generators to overcome the problem of interruptions in the live rail. Three main-line diesel-electric locomotives were completed after nationalization of the SR in 1948. All were carried on bogies, as was Bulleid's last steam locomotive design for the SR, the "Leader" class 0−6−6−0 originally intended to meet a requirement for a large, passenger tank locomotive. The first was completed after nationalization of the SR, but the project never went beyond trials. Marginally more successful was a double-deck, electric, suburban, multiple-unit train completed in 1949, with alternate high and low compartments to increase train capacity but not length. The main disadvantage was the slow entry and exit by passengers, and the type was not perpetuated, although the prototype train ran in service until 1971.In 1951 Bulleid moved to Coras Iompair Éireann, the Irish national transport undertaking, as Chief Mechanical Engineer. There he initiated a large-scale plan for dieselization of the railway system in 1953, the first such plan in the British Isles. Simultaneously he developed, with limited success, a steam locomotive intended to burn peat briquettes: to burn peat, the only native fuel, had been a long-unfulfilled ambition of railway engineers in Ireland. Bulleid retired in 1958.[br]BibliographyBulleid took out six patents between 1941 and 1956, covering inter alia valve gear, boilers, brake apparatus and wagon underframes.Further ReadingH.A.V.Bulleid, 1977, Bulleid of the Southern, Shepperton: Ian Allan (a good biography written by the subject's son).C.Fryer, 1990, Experiments with Steam, Wellingborough: Patrick Stephens (provides details of the austerity 0–6–0, the "Leader" locomotive and the peat-burning locomotive: see Chs 19, 20 and 21 respectively).PJGRBiographical history of technology > Bulleid, Oliver Vaughan Snell
-
3 Sellers, William
SUBJECT AREA: Mechanical, pneumatic and hydraulic engineering[br]b. 19 September 1824 Upper Darby, Pennsylvania, USAd. 24 January 1905 Philadelphia, Pennsylvania, USA[br]American mechanical engineer and inventor.[br]William Sellers was educated at a private school that had been established by his father and other relatives for their children, and at the age of 14 he was apprenticed for seven years to the machinist's trade with his uncle. At the end of his apprenticeship in 1845 he took charge of the machine shop of Fairbanks, Bancroft \& Co. in Providence, Rhode Island. In 1848 he established his own factory manufacturing machine tools and mill gearing in Philadelphia, where he was soon joined by Edward Bancroft, the firm becoming Bancroft \& Sellers. After Bancroft's death the name was changed in 1856 to William Sellers \& Co. and Sellers served as President until the end of his life. His machine tools were characterized by their robust construction and absence of decorative embellishments. In 1868 he formed the Edgemoor Iron Company, of which he was President. This company supplied the structural ironwork for the Centennial Exhibition buildings and much of the material for the Brooklyn Bridge. In 1873 he reorganized the William Butcher Steel Works, renaming it the Midvale Steel Company, and under his presidency it became a leader in the production of heavy ordnance. It was at the Midvale Steel Company that Frederick W. Taylor began, with the encouragement of Sellers, his experiments on cutting tools.In 1860 Sellers obtained the American rights of the patent for the Giffard injector for feeding steam boilers. He later invented his own improvements to the injector, which numbered among his many other patents, most of which related to machine tools. Probably Sellers's most important contribution to the engineering industry was his proposal for a system of screw threads made in 1864 and later adopted as the American national standard.Sellers was a founder member in 1880 of the American Society of Mechanical Engineers and was also a member of many other learned societies in America and other countries, including, in Britain, the Institution of Mechanical Engineers and the Iron and Steel Institute.[br]Principal Honours and DistinctionsChevalier de la Légion d'honneur 1889. President, Franklin Institute 1864–7.Further ReadingJ.W.Roe, 1916, English and American Tool Builders, New Haven; reprinted 1926, New York, and 1987, Bradley, Ill. (describes Sellers's work on machine tools).Bruce Sinclair, 1969, "At the turn of a screw: William Sellers, the Franklin Institute, and a standard American thread", Technology and Culture 10:20–34 (describes his work on screw threads).RTS -
4 Brotan, Johann
SUBJECT AREA: Railways and locomotives[br]b. 24 June 1843 Kattau, Bohemia (now in the Czech Republic)d. 20 November 1923 Vienna, Austria[br]Czech engineer, pioneer of the watertube firebox for steam locomotive boilers.[br]Brotan, who was Chief Engineer of the main workshops of the Royal Austrian State Railways at Gmund, found that locomotive inner fireboxes of the usual type were both expensive, because the copper from which they were made had to be imported, and short-lived, because of corrosion resulting from the use of coal with high sulphur content. He designed a firebox of which the side and rear walls comprised rows of vertical watertubes, expanded at their lower ends into a tubular foundation ring and at the top into a longitudinal water/steam drum. This projected forward above the boiler barrel (which was of the usual firetube type, though of small diameter), to which it was connected. Copper plates were eliminated, as were firebox stays.The first boiler to incorporate a Brotan firebox was built at Gmund under the inventor's supervision and replaced the earlier boiler of a 0−6−0 in 1901. The increased radiantly heated surface was found to produce a boiler with very good steaming qualities, while the working pressure too could be increased, with consequent fuel economies. Further locomotives in Austria and, experimentally, elsewhere were equipped with Brotan boilers.Disadvantages of the boiler were the necessity of keeping the tubes clear of scale, and a degree of structural weakness. The Swiss engineer E. Deffner improved the latter aspect by eliminating the forward extension of the water/steam drum, replacing it with a large-diameter boiler barrel with the rear section of tapered wagon-top type so that the front of the water/steam drum could be joined directly to the rear tubeplate. The first locomotives to be fitted with this Brotan-Deffner boiler were two 4−6−0s for the Swiss Federal Railways in 1908 and showed very favourable results. However, steam locomotive development ceased in Switzerland a few years later in favour of electrification, but boilers of the Brotan-Deffner type and further developments of it were used in many other European countries, notably Hungary, where more than 1,000 were built. They were also used experimentally in the USA: for instance, Samuel Vauclain, as President of Baldwin Locomotive Works, sent his senior design engineer to study Hungarian experience and then had a high-powered 4−8−0 built with a watertube firebox. On stationary test this produced the very high figure of 4,515 ihp (3,370 kW), but further development work was frustrated by the trade depression commencing in 1929. In France, Gaston du Bousquet had obtained good results from experimental installations of Brotan-Deffner-type boilers, and incorporated one into one of his high-powered 4−6−4s of 1910. Experiments were terminated suddenly by his death, followed by the First World War, but thirty-five years later André Chapelon proposed using a watertube firebox to obtain the high pressure needed for a triple-expansion, high-powered, steam locomotive, development of which was overtaken by electrification.[br]Further ReadingG.Szontagh, 1991, "Brotan and Brotan-Deffner type fireboxes and boilers applied to steam locomotives", Transactions of the Newcomen Society 62 (an authoritative account of Brotan boilers).PJGR -
5 Stevens, John
[br]b. 1749 New York, New York, USAd. 6 March 1838 Hoboken, New Jersey, USA[br]American pioneer of steamboats and railways.[br]Stevens, a wealthy landowner with an estate at Hoboken on the Hudson River, had his attention drawn to the steamboat of John Fitch in 1786, and thenceforth devoted much of his time and fortune to developing steamboats and mechanical transport. He also had political influence and it was at his instance that Congress in 1790 passed an Act establishing the first patent laws in the USA. The following year Stevens was one of the first recipients of a US patent. This referred to multi-tubular boilers, of both watertube and firetube types, and antedated by many years the work of both Henry Booth and Marc Seguin on the latter.A steamboat built in 1798 by John Stevens, Nicholas J.Roosevelt and Stevens's brother-in-law, Robert R.Livingston, in association was unsuccessful, nor was Stevens satisfied with a boat built in 1802 in which a simple rotary steam-en-gine was mounted on the same shaft as a screw propeller. However, although others had experimented earlier with screw propellers, when John Stevens had the Little Juliana built in 1804 he produced the first practical screw steamboat. Steam at 50 psi (3.5 kg/cm2) pressure was supplied by a watertube boiler to a single-cylinder engine which drove two contra-rotating shafts, upon each of which was mounted a screw propeller. This little boat, less than 25 ft (7.6 m) long, was taken backwards and forwards across the Hudson River by two of Stevens's sons, one of whom, R.L. Stevens, was to help his father with many subsequent experiments. The boat, however, was ahead of its time, and steamships were to be driven by paddle wheels until the late 1830s.In 1807 John Stevens declined an invitation to join with Robert Fulton and Robert R.Living-ston in their development work, which culminated in successful operation of the PS Clermont that summer; in 1808, however, he launched his own paddle steamer, the Phoenix. But Fulton and Livingston had obtained an effective monopoly of steamer operation on the Hudson and, unable to reach agreement with them, Stevens sent Phoenix to Philadelphia to operate on the Delaware River. The intervening voyage over 150 miles (240 km) of open sea made Phoenix the first ocean-going steamer.From about 1810 John Stevens turned his attention to the possibilities of railways. He was at first considered a visionary, but in 1815, at his instance, the New Jersey Assembly created a company to build a railway between the Delaware and Raritan Rivers. It was the first railway charter granted in the USA, although the line it authorized remained unbuilt. To demonstrate the feasibility of the steam locomotive, Stevens built an experimental locomotive in 1825, at the age of 76. With flangeless wheels, guide rollers and rack-and-pinion drive, it ran on a circular track at his Hoboken home; it was the first steam locomotive to be built in America.[br]Bibliography1812, Documents Tending to Prove the Superior Advantages of Rail-ways and Steam-carriages over Canal Navigation.He took out patents relating to steam-engines in the USA in 1791, 1803, and 1810, and in England, through his son John Cox Stevens, in 1805.Further ReadingH.P.Spratt, 1958, The Birth of the Steamboat, Charles Griffin (provides technical details of Stevens's boats).J.T.Flexner, 1978, Steamboats Come True, Boston: Little, Brown (describes his work in relation to that of other steamboat pioneers).J.R.Stover, 1961, American Railroads, Chicago: University of Chicago Press.Transactions of the Newcomen Society (1927) 7: 114 (discusses tubular boilers).J.R.Day and B.G.Wilson, 1957, Unusual Railways, F.Muller (discusses Stevens's locomotive).PJGR -
6 Seguin, Marc
[br]b. 20 April 1786 Annonay, Ardèche, Franced. 24 February 1875 Annonay, Ardèche, France[br]French engineer, inventor of multi-tubular firetube boiler.[br]Seguin trained under Joseph Montgolfier, one of the inventors of the hot-air balloon, and became a pioneer of suspension bridges. In 1825 he was involved in an attempt to introduce steam navigation to the River Rhône using a tug fitted with a winding drum to wind itself upstream along a cable attached to a point on the bank, with a separate boat to transfer the cable from point to point. The attempt proved unsuccessful and was short-lived, but in 1825 Seguin had decided also to seek a government concession for a railway from Saint-Etienne to Lyons as a feeder of traffic to the river. He inspected the Stockton \& Darlington Railway and met George Stephenson; the concession was granted in 1826 to Seguin Frères \& Ed. Biot and two steam locomotives were built to their order by Robert Stephenson \& Co. The locomotives were shipped to France in the spring of 1828 for evaluation prior to construction of others there; each had two vertical cylinders, one each side between front and rear wheels, and a boiler with a single large-diameter furnace tube, with a watertube grate. Meanwhile, in 1827 Seguin, who was still attempting to produce a steamboat powerful enough to navigate the fast-flowing Rhône, had conceived the idea of increasing the heating surface of a boiler by causing the hot gases from combustion to pass through a series of tubes immersed in the water. He was soon considering application of this type of boiler to a locomotive. He applied for a patent for a multi-tubular boiler on 12 December 1827 and carried out numerous experiments with various means of producing a forced draught to overcome the perceived obstruction caused by the small tubes. By May 1829 the steam-navigation venture had collapsed, but Seguin had a locomotive under construction in the workshops of the Lyons-Sain t- Etienne Railway: he retained the cylinder layout of its Stephenson locomotives, but incorporated a boiler of his own design. The fire was beneath the barrel, surrounded by a water-jacket: a single large flue ran towards the front of the boiler, whence hot gases returned via many small tubes through the boiler barrel to a chimney above the firedoor. Draught was provided by axle-driven fans on the tender.Seguin was not aware of the contemporary construction of Rocket, with a multi-tubular boiler, by Robert Stephenson; Rocket had its first trial run on 5 September 1829, but the precise date on which Seguin's locomotive first ran appears to be unknown, although by 20 October many experiments had been carried out upon it. Seguin's concept of a multi-tubular locomotive boiler therefore considerably antedated that of Henry Booth, and his first locomotive was completed about the same date as Rocket. It was from Rocket's boiler, however, rather than from that of Seguin's locomotive, that the conventional locomotive boiler was descended.[br]BibliographyFebruary 1828, French patent no. 3,744 (multi-tubular boiler).1839, De l'Influence des chemins de fer et de l'art de les tracer et de les construire, Paris.Further ReadingF.Achard and L.Seguin, 1928, "Marc Seguin and the invention of the tubular boiler", Transactions of the Newcomen Society 7 (traces the chronology of Seguin's boilers).——1928, "British railways of 1825 as seen by Marc Seguin", Transactions of the Newcomen Society 7.J.B.Snell, 1964, Early Railways, London: Weidenfeld \& Nicolson.J.-M.Combe and B.Escudié, 1991, Vapeurs sur le Rhône, Lyons: Presses Universitaires de Lyon.PJGR -
7 Phillips, Horatio Frederick
SUBJECT AREA: Aerospace[br]b. 2 February 1845 London, Englandd. 15 July 1926 Hampshire, England[br]English aerodynamicist whose cambered two-surface wing sections provided the foundations for aerofoil design.[br]At the age of 19, Phillips developed an interest in flight and constructed models with lightweight engines. He spent a large amount of time and money over many years, carrying out practical research into the science of aerodynamics. In the early 1880s he built a wind tunnel with a working section of 15 in. by 10 in. (38 cm by 25 cm). Air was sucked through the working section by an adaptation of the steam injector used in boilers and invented by Henry Giffard, the airship pioneer. Phillips tested aerofoils based on the cross-section of bird's wings, with a greater curvature on the upper surface than the lower. He measured the lift and drag and showed that the major component of lift came from suction on the upper surface, rather than pressure on the lower. He took out patents for his aerofoil sections in 1884 and 1891. In addition to his wind-tunnel test, Phillips tested his wing sections on a whirling arm, as used earlier by Cayley, Wenham and Lilienthal. After a series of tests using an arm of 15 ft (4.57 m) radius, Phillips built a massive whirling arm driven by a steam engine. His test pieces were mounted on the end of the arm, which had a radius of 50 ft (15.24 m), giving them a linear speed of 70 mph (113 km/h). By 1893 Phillips was ready to put his theories to a more practical test, so he built a large model aircraft driven by a steam engine and tethered to run round a circular track. It had a wing span of 19 ft (5.79 m), but it had fifty wings, one above the other. These wings were only 10 in. (25 cm) wide and mounted in a frame, so it looked rather like a Venetian blind. At 40 mph (64 km/h) it lifted off the track. In 1904 Phillips built a full-size multi-wing aeroplane with twenty wings which just lifted off the ground but did not fly. He built another multi-wing machine in 1907, this time with four Venetian blind' frames in tandem, giving it two hundred wings! Phillips made a short flight of almost 500 ft (152 m) which could be claimed to be the first powered aeroplane flight in England by an Englishman. He retired from flying at the age of 62.[br]Bibliography1900, "Mechanical flight and matters relating thereto", Engineering (reprint).1891–3, "On the sustentation of weight by mechanical flight", Aeronautical Society of Great Britain 23rd Report.Further ReadingJ.Laurence Pritchard, 1957, "The dawn of aerodynamics", Journal of the Royal Aeronautical Society (March) (good descriptions of Phillips's early work and his wind tunnel).J.E.Hodgson, 1924, The History of Aeronautics in Great Britain, London.F.W.Brearey, 1891–3, "Remarks on experiments made by Horatio Phillips", Aeronautical Society of Great Britain 23rd Report.JDSBiographical history of technology > Phillips, Horatio Frederick
См. также в других словарях:
Steam locomotive — A steam locomotive is a locomotive powered by steam. The term usually refers to its use on railways, but can also refer to a road locomotive such as a traction engine or steamroller.Steam locomotives dominated rail traction from the mid 19th… … Wikipedia
Three-drum boilers — Three drum boiler, casing removed … Wikipedia
High pressure steam locomotive — A high pressure steam locomotive is a steam locomotive with a boiler that operates at pressures well above what would be considered normal. In the later years of steam, boiler pressures were typically 200 to 250 PSI (1.4 to 1.7 MPa). High… … Wikipedia
Timeline of steam power — See Steam engine, Steam power during the Industrial Revolution. Steam power developed slowly over a period of several hundred years, progressing through expensive and fairly limited devices in the early 1600s, to useful pumps for mining in 1700,… … Wikipedia
Chaplin's Patent Distilling Apparatus with Steam Pump — Chaplins patent sea water distilling apparatus. Alexander Chaplin Co. (also known as A.C. and Co., Alex. Chaplin Co.) was an important and highly regarded[1] engineering and manufacturing syndicat … Wikipedia
History of the steam engine — This article primarily deals with the history of the reciprocating type steam engine. The parallel development of turbine type engines is described in the steam turbine article. The history of the steam engine stretches back as far as the first… … Wikipedia
Benjamin F. Isherwood — Benjamin Franklin Isherwood (October 6, 1822 ndash; June 19, 1915) was an engineering officer in the United States Navy during the early days of steam powered warships. He served as a ship s engineer during the Mexican American War, and after the … Wikipedia
Fusible plug — A fusible plug is a threaded metal plug, usually made out of bronze, brass, or gunmetal. The plug typically has a tapered hole drilled completely through its length. This hole is then sealed with a metal of low melting point, usually lead or tin … Wikipedia
Samuel Morey — Infobox Engineer image size = 150px caption = Samuel Morey name = Samuel Morey nationality = American birth date = October 23, 1762 birth place = Hebron, Connecticut death date = April 17, 1843 death place = education = spouse = parents =… … Wikipedia
Coal-water slurry fuel — (CWSF or CWS or CWF) is a fuel which consists of fine coal particles suspended in water. Presence of water in CWS reduces harmful emissions into the atmosphere, makes the coal explosion proof, makes use of coal equivalent to use of liquid fuel (e … Wikipedia
Richard Trevithick — Infobox Scientist name = Richard Trevithick box width = image width = 150px caption = Richard Trevithick, by John Linnell (1792 1882) birth date = April 13, 1771 birth place = Cornwall death date = April 22, 1833 (aged 62) death place = Dartford … Wikipedia
